The Spring SOP deforms and moves the input geometry using spring "forces" on the edges of polygons and on masses attached to each point.
Geometry is deformed using forces that simulate simple physics on the points and edges. A simulated "mass" is assigned to each point. Its primitive edges act as "springs" which oppose the forces, and pull the points back toward their original positions. When the springs are stretched by the forces, they try to pull the points back. The points do not stop moving when they return to their original positions, however, but continue to oscillate because of their mass, until the oscillation dies out.
Forces which act upon the points are as follows:
- external force (gravity)
- wind (similar to external force)
- turbulence (chaotic forces)
The greater the drag value, or smaller the mass, the faster the oscillation dies out.
Parameters - State Page
timepreroll - How many seconds of the simulation to bypass, after the reset time is reached. For example, if you put the number 33 into this field (and reset is at
$TSTART), frame one will show the simulation that was at a time of 33 seconds. In other words, the first thirty-two seconds have been bypassed, and the time at thirty-three seconds is shifted to frame one. The first thirty-two seconds must still be calculated in order to compute the status of the points, so you will notice some delay upon reset.
timeinc - The Time Inc parameter determines how often to cook the SOP. By default, this parameter is set to
1/$FPS. This means that the SOP will cook once for every frame. When complex dynamics are involved, the SOP may require more frequent cooking for increased mathematical accuracy. To get sub-frame accuracy in the cooking, set the Time Inc to something smaller than
1/$FPS . For example, setting the Time Inc to
0.5/$FPS will mean that the SOP gets cooked twice for every frame.
Note: Never set this parameter greater than
accurate - This option makes the nodes move more accurately between frames by calculating their trajectories for fractional frame values.
attractmode - ⊞ -
- All Points
all- All point attractors affect all particles (or points).
- Single Point per Particle
single- When enabled, each particle is assigned a single attractor point, and is affected by only that point. Assignment is done by point number modulo the total number of attractor points.
reset - While On resets the spring effect of the SOP.
resetpulse - Instantly reset the spring effect.
Parameters - Forces Page
external - ⊞ - Forces of gravity acting on the points. When drag is zero, the points can accelerate with no limit on their speed.
wind - ⊞ - Wind forces acting on the points. Similar to external force. Using wind (and no other forces, such as turbulence), the points will not exceed the wind velocity.
turb - ⊞ - The amplitude of turbulent (chaotic) forces along each axis. Use positive values, if any.
period - A small period means that the turbulence varies quickly over a small area, while a larger value will cause points close to each other to be affected similarly.
seed - Random number seed for the simulation.
Parameters - Nodes Page
fixed - This is a point group. All points in the point group will remain unaffected by the forces. Also see the Group SOP for notes on how to specify point ranges.
Fixed Points go to Source Positions
revertfixed - Determines whether or not points in the Fixed Points group should be moved to the positions of the corresponding points in the Source geometry.
Copy Groups from Source
copygroups - Determines if the Spring SOP should copy groups from the Source geometry at each frame. This lets you specify the name of an animating group in the Fixed Points field, and the contents of this group will be kept up to date.
Add Mass Attribute
domass - When selected, the Mass is computed for the deforming geometry.
mass - Mass of each point. Heavier points take longer to get into motion, and longer to stop.
Add Drag Attribute
dodrag - When selected, the geometry is deformed by the Drag attribute.
drag - Drag of each point.
springbehavior - ⊞ - How the springs will behave:
- Hooke's Law
hooke- Springs will work according to Hooke's Law. This is generally more stable than Normalized Displacement.
- Hooke's Law: Force = Displacement Spring constant
- Normalize Displacement
normalize- Similar to Hooke's Law except that the displacement is normalized to the original length of the Spring.
springk - The spring constant. How tight the springs are. Increase this value to make the springs tighter and thus make the object more rigid. As this number becomes higher, the springs can oscillate out of control. Decrease the Time Inc if this happens.
tension - The Initial k constant of the geometry before being deformed by the spring operation.
Parameters - Limits Page
+ Limit Plane
limitpos - ⊞ - The points will bounce off the limit planes when it reaches them. The six limit plane fields define a bounding cube. The default settings are one thousand units away, which is very large. Reduce the values to about one to see the effect.
- Limit Plane
limitneg - ⊞ - The points will bounce off the limit planes when it reaches them. The six limit plane fields define a bounding cube. The default settings are one thousand units away, which is very large. Reduce the values to about one to see the effect.
hit - ⊞ - Control over what happens when the geometry hits either the six collision planes or the collision object. The options are:
- Bounce on Contact
bounce- Geometry will bounce upon contact with the Collision input.
- Stick on Contact
stick- Geometry will stick to the Collision input upon contact.
gaintan - Friction parameters which can be regarded as energy-loss upon collision. The first parameter affects the energy loss (gain) perpendicular to the surface. 0 means all energy (velocity) is lost, 1 means no energy is lost perpendicular to surface. The second parameter is the energy gain tangent to the surface.
gainnorm - Friction parameters which can be regarded as energy-loss upon collision. The first parameter affects the energy loss (gain) perpendicular to the surface. 0 means all energy (velocity) is lost, 1 means no energy is lost perpendicular to surface. The second parameter is the energy gain tangent to the surface.
- Input 0 -
- Input 1 -
- Input 2 -
|• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •|
An Operator Family that reads, creates and modifies 3D polygons, curves, NURBS surfaces, spheres, meatballs and other 3D surface data.
The frame rate that TouchDesigner's Timeline uses. Equal to the Frames per Second value
Each SOP has a list of Points. Each point has an XYZ 3D position value plus other optional attributes. Each polygon Primitive is defined by a vertex list, which is list of point numbers.
To pulse a parameter is to send it a signal from a CHOP or python or a mouse click that causes a new action to occur immediately. A pulse via python is via the
.pulse() function on a pulse-type parameter, such as Reset in a Speed CHOP. A pulse from a CHOP is typically a 0 to 1 to 0 signal in a channel.